Naim-audio NAC-N 272 User Manual download pdf (Page 4)

1. Installing and Connecting

1.1 Stand your NAC-N 272 on an appropriate, stable surface. Make sure it is well ventilated.

1.2 Check that the mains voltage specified on the NAC-N 272 rear panel is appropriate for your country. Insert the supplied power

supply upgrade link plug in the rear panel Burndy socket and connect the NAC-N 272 to the mains supply using the supplied

mains cable. Do not switch on the NAC-N 272 until all other connections have been made.

1.3 Identify the rear panel Signal Ground Switch and select the chassis option unless your NAC-N 272 is connected in a hi-fi

system incorporating another earthed source component (all Naim CD players, for example), or mains hum is audible through

the speakers when it is switched on.

1.4 If the optional DAB/FM Radio Module is fitted, a suitable aerial should be connected to the DAB/FM aerial socket.

1.5 Connect a power amplifier, active crossover or multiple power amplifiers to one or both of the NAC-N 272 preamp output

sockets. NAC-N 272 preamp output sockets are also suitable for the connection of a subwoofer. Your Naim retailer will be able

to supply appropriate cables if required.

1.6 To play audio from internet radio stations, UPnP™ servers, Spotify

Connect, or other Naim streamer units the NAC-N 272

must be connected to the internet via a network router. Either connect the NAC-N 272 network socket to your network router

using an Ethernet cable, or connect the supplied Wi-Fi antenna to the rear panel Wi-Fi aerial socket.

1.7 For NAC-N 272 to play audio from Bluetooth

streaming devices, the supplied Bluetooth antenna must be attached to the rear

panel Bluetooth aerial socket.

1.8 If your NAC-N 272 is to play audio files stored on a USB storage device, such as an iOS device or a memory stick, connect it,

using an appropriate cable if necessary, to the front panel USB socket.

1.9 If any external audio sources are to be used with your NAC-N 272, connect them using the appropriate cables to one or more

of the rear panel analogue or digital inputs.

2. Switching On and Getting Started

2.1 Once all connections have been made, switch on your NAC-N 272 using either its rear panel on/off switch or the external

power supply on/off. The NAC-N 272 will display a welcome screen and select its Analogue 1 input or, if it has been previously

used, the last input selected.

2.2 For initial setup purposes your NAC-N 272 is best controlled from its remote handset. Use the navigation (56) keys to select

inputs or menu items and the ok/list key to confirm selections. To return to a previous menu use the left (3) key.

2.3 The NAC-N 272 interface language can be changed. Enter Setup Mode and select Language.

NAC-N 272 • English

Note: Full NAC-N 272 installation and operational information can be

found in the Reference Manual available at: www.naimaudio.com

Note 1.9: Most UMS (Universal Mass Storage) USB devices are compatible

with the NAC-N 272 USB audio input. Such devices might include portable

digital music players, smart-phones, tablet computers, USB memory sticks

and memory card readers.

Note 1.7 & 1.8: NAC-N 272 is supplied with both Wi-Fi and Bluetooth

aerials. Each aerial must be fitted to the correct rear panel aerial socket.

The Bluetooth aerial is the shorter one of the two.

Note 2.1: If your NAC-N 272 is left unused it will switch to displaying the

time after two minutes. This delay time can be adjusted via the setup

menus. If the clock is not set it will display “No Time”.

Setup 1/10

 Language

Inputs

4 Analogue O utputs

Headphones

Enter Setup Mode by pressing the handset

setup ( ) key. Navigate setup menus by

using the navigation (563) keys. Select

options by pressing the ok/list key. Leave

Setup Mode by pressing the setup or exit

key.

Note 1.2: If your NAC-N 272 is to be powered by an external power supply,

remove the power supply upgrade link plug and connect the external

power supply using the appropriate Burndy cable. Do not connect the

NAC-N 272 mains cable.

Important: XPS power supplies with serial numbers below 188015 are not

compatible with the NAC-N 272 and should not be used. Contact your

local retailer or distributor for more information.

Note 1.5: The NAC-N 272 RCA phono preamp output sockets are disabled

by default. They can be enabled in the Analogue Outputs setup menu.

1 2 3 4 5 6 7 8 9 ... 35 36

Comments to this Manuals

No comments

Naim-audio NAC-N 272 User Manual Page 4

Comments to this Manuals

Related products and manuals for Receivers and Amplifiers Naim-audio NAC-N 272